Matchbox Curtiss SBC4 Hell Diver on Deck

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
Hi All,

I've always wanted to know if there was a last bi-plane in US Navy WW2 service. It turned out to be the Curtiss SBC4 Helldiver. Although it never went to battle it had the distiction to be the last bi-plane in US carrier service.

I featured this in the last MM forum and I bet many here have not seen it come up from the start...

102.jpg

This old Matchbox kit was amongst my stash for quite a while and it was time I had a go at it...

1.jpg 1a.jpg

The parts were crisp and they came with the usual multi coloured plastic. The horizontal surfaces like the wings panel lines are engraved, the fuselage was raised so scribing was needed for that.

1b.jpg 1c.jpg

The interior was very spartan basically empty ...I added ribbing and basic throttle box and firewalls.

2.jpg 2a.jpg

The seats were just L shaped plastic so plastic card and some shaping took care of that.

2b.jpg 3.jpg

More gizmology was added including tracks to the floor and hump for the joystick. I drilled holes to the back firewall to simulate light weight panelling.

4.jpg 5.jpg6.jpg 7.jpg

I dry fitted the halves together to check if the additions blocked fitting.

8.jpg

Next painting the interior...
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
I sprayed the assembly with interior green including the undercarriage bay...the green may look a bit glaring on camera but it's a bit duller

9.jpg 11.jpg

Then I slowly picked out details with paint.

12.jpg 13.jpg

A wash was applied to the right fuselage...that helped bring out more detail.

14.jpg 15.jpg

Then the left side got attention...

16.jpg 17.jpg

Reference showed oxigen bottles so some were fashioned from clear sprue...I don't know why I used clear sprue as any plastic rod could have been used.

17a.jpg 17b.jpg17c.jpg 17d.jpg

Wash was applied to this side...looks a little heavy but looked alright once the fuselage halves were closed.

18.jpg 19.jpg20.jpg 21.jpg

Seat belts made from wire and tape were glued on...

22.jpg 23.jpg24.jpg Another dry fit to see if everything was covered...next the clear canopy was tackled.

Cheers,
Richard
 

Jim R

SMF Supporter
Joined
Apr 27, 2018
Messages
13,597
Points
113
Location
Shropshire
First Name
Jim
Hi Richard
I don't think I remember this. Could be that my old brain ain't what is was but it does mean I can enjoy watching this come together. Off to your usual, painstaking start.
Jim
 

Dave Ward

Still Trying New Things
SMF Supporter
Joined
Apr 27, 2018
Messages
8,559
Points
113
Location
South Gloucestershire
First Name
David
The SBC-4 was one of my favourite Matchbox aircraft, I must have made it 4 or 5 times, as the US Navy, and the RAF Cleveland. Heller also made a SBC-4 ( different moulds ). The Boeing P-12 was also made in several versions. The Matchbox biplanes were all pretty good, the Fury being pretty good. I made the Siskin recently.............. matchbox 1-72 Siskin Dave Ward 01.jpg

matchbox 1-72 Siskin Dave Ward 03.jpg

Sadly this was the model that convinced me that I could no longer do 1/72 aircraft models
justice - too small!
Dave
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
Hi Guys...thanks for dropping in for a look and commenting.

Jimbo, nothing like a refresher to get the brain juices flowing. This is enjoyable pain.
Ian, great to have you along.
Dave, wow...you must have quite a collection of the SBC4's. I remember your Siskin, got one myself. Sadly deteriorating eyesight can get the better of us. I'm not looking forward to the day that I have to switch to larger kits.

Cheers,
Richard
 

Steve Jones

Steve Jones Scale Modelling Site
Joined
Apr 27, 2018
Messages
6,698
Points
113
Location
Plymouth
First Name
Steve
Oooooh! Thats nice. A wonderful subject to build. Looking forward to seeing some more of your magic
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
Hi Steve, abracadabra and poof! you're here. Thanks. Nice to have you on board the Matchbox journey.

Cheers,
Richard
 

JR

Member of the Rabble and Pyromania Consultant
SMF Supporter
Joined
May 26, 2015
Messages
17,215
Points
113
Location
lincs
First Name
John
Keeping up with these little gems .
Why was green as internal colour picked Richard ?
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
Good question John, at the time I took for granted that all US aircraft cockpit interior was interior green and the rest insignia green. It should be silver as planes of this era just prior to WW2 had their cockpits in silver just like wheel wells for the Spitfire and Typhoon were in silver as well.
By the time I realised was too late as the fuselage had been glued so I've got to live with it.

Cheers,
Richard
 
  • Like
Reactions: JR

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
For once the Matchbox clear parts were slightly undersized but the frames were still bulging and plastic thick. I wanted to pose the cockpit canopy slide back and to do this I had to thin the pilots canopy and use the gunners canopy as the canopy just behind the pilot

25a.jpg 25b.jpg

Sanding and polishing achieved the thickness that I needed. Joints needed extra plastic shims for a gradual slop towards the tail.

25c.jpg 26.jpg

All surface elevators were cut and repositioned including the tail.

27.jpg 27a.jpg27b.jpg 28.jpg

Gaps were filled and sanded.

29.jpg 30.jpg31.jpg 32.jpg

Finer putty was applied and final sanding done.

33.jpg 34.jpg

The tail was positioned to follow the elevators for a right turn.

34a.jpg

Next ...engine cowling

Cheers,
Richard
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
Here's the engine and cowling...the part look ok so I didn't bother detailing it. Spraye it interior green...should have been insignier yellow/green...back then everything was interior green to me.:rolling:

35.jpg 36.jpg

But I did slightly detail the cowling by drilling out the air scoop

37.jpg 38.jpg

Dry fitted the parts and propeller...the propeller had a pronounced distance from the cowling so I shortened and moved it closer. Later I painted the pistons and push rods flat black and dry brushed silver to bring out raised detail.

39.jpg 40.jpg

Unfortunately I don't have pictures of the painted engine.

Cheers,
Richard
 

Steve Jones

Steve Jones Scale Modelling Site
Joined
Apr 27, 2018
Messages
6,698
Points
113
Location
Plymouth
First Name
Steve
Why not? Your not letting your standards drop are you Richard?:smiling2::smiling5:

Terrific work on the fuselage
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
Hi Steve, well the eagerness to assemble the parts got the better of me and I just forgot to photograph the progress. Basic black and silver dry brushing and dirty wash was all it needed.

Cheers,
Richard
 

colin m

Moderator
Staff member
Moderator
SMF Supporter
Joined
Dec 26, 2008
Messages
8,572
Points
113
Location
Stafford, UK
First Name
Colin
Lovely. An old, sorry, vintage Matchbox kit. It's great to see one being built. Nice job to, with all the extra detail.
 

Richard48

SMF Supporter
Joined
Apr 27, 2018
Messages
1,395
Points
113
Location
Clacton on sea
First Name
Richard
Nice trip down nostalgia lane chaps.When i got into models aged 9 our local newsagents and model shops stocked Matchbox kits.I dont know about you chaps but the wonderful Matchbox box art grabbed my attention and eager paws.I remember having a tooth out at Dentist and mum treating me to the monoplane Matchbox helldiver model.I loved Matchbox kits and now nearly 50 i look back with affection and a tear or two at a bygone age in the 70s when life wasnt so much rush here and there.
Richard.
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
Thanks Collin and Richard. Nice to have jolted old memories on a vintage kit. I still like building Matchbox kits when I get hold of any because of their clean rivetless molds.

Cheers,
Richard
 

rtfoe

SMF Supporter
Joined
Apr 29, 2018
Messages
7,465
Points
113
Location
Malaysia
First Name
Richard
I plugged every opening with soaked tissue before spraying a primer coat...

41.jpg 42.jpg43.jpg 44.jpg

When satisfied that there were no blemishes to fill and sand I did a pre-shade with black.

45.jpg 46.jpg

Vintage kits come with vintage decals that desintegrate right before your eyes in 5 seconds...talk about mission impossible. Next is mission possible.

Cheers,
Richard
 
Top